CNC Set 4 Axis Breakout Board & DM432 Stepper Motor For DIY Router/Mill/Plasma

Description

Store category
Sign Up Now !
You may also like
CNC Set 4 Axis Breakout Board & DM432 Stepper Motor For DIY Router/Mill/Plasma
Product Description
shipping notice
Can't not ship to Puerto Rico,Alaska/Hawaii
Brand
Unbranded
MPN
Does Not Apply
Features:
1.High torque, More smooth movement
2.High efficiency, energy-saving, low noise, low vibration, high start torque, low start current and reliable performance.
This item includes:
4 pcs Nema 17 stepper motor with
48
oz. in=4Kg.cm,4 leads, 1.7A
4 pcs Stepper motor driver DM
432
, peak
3.5
A,
32micsteps
1 pc Power supply 200W-24V
1 pc breakout board & 1 pc parallal cable
1. Nema 17 stepper motor:
Technical Specifications
Frame Size:                NEMA23
Phase:             2 Phase
Step Angle:                1.8 degree
Current:
1.7 A
Rated Voltage:  2.55 V
Resistance:  1.5Ohm/phase
Inductance:  2.8 mH/phase
Holding torque:  48 oz-in (0.40N.m   4000G-cm=40N.cm)
Detent torque: 2.2 N.cm
Rotor inertia: 54 g.cm²
Number of wire leads: 4 (Black  A+ ,Green A- ,Red B+ ,Blue B-)
Length: 40 mm
Matched drive:
DM4
32
Shaft:
Single Shaft
Front shaft length
：
24mm
The diameter for motor shaft is
：
5mm
The diameter of axle is 5mm and the length of the shaft is 24mm.
2. Stepper motor driver DM432, peak 3.5A, 32 micstep
Features:
l High performance, low price
l Average current control, 2-phase
s
tepper motor drive
l Supply voltage from
9
VDC to
40
VDC
l Opto-isolated signal I/O
l Overvoltage, under voltage, overcorrect, phase short circuit protection
l
7
channels subdivision and automatic idle-current reduction
l 8 channels output phase current setting
l Offline command input terminal
l Motor torque is related with speed, but not related with step/revolution
l High start speed
l High hording torque under high speed
Electrical specification:
Input voltage
9
-
40
VDC
Input current
＜
5
A
Output current
0.
5
A-
4
A
Consumption
Consumption：
16
0W；
Temperature
Working Temperature -10～45℃；
Stocking temperature -40℃～70℃
Humidity
Not condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
20
0G
Connector Pins    Configurations
Pin Function
Details
PUL +,PUL-
Pulse signal, PUL+ is the positive end of pulses input pin
PUL- is the negative end of pulse input pin
DIR+,DIR-
DIR signal: DIR+ is the positive end of direction input pin
DIR- is the negative end of direction input pin
EN+
EN+ is the positive end of
Motor offline control.
EN-
EN- is the negative end of
Motor offline control
Function choice
( Using DIP pins to achieve this function)
1
)
Subdivision setting:
Dip switches 1, 2, and 3 correspond to S1, S2, and S3, respectively.
S1
S2
S3
Pulse/rev
Micro
ON
ON
ON
NC
NC
O
N
ON
O
FF
200
1
ON
OFF
ON
400
2/
A
OFF
O
N
ON
400
2/B
ON
O
FF
OFF
800
4
OFF
ON
OFF
1600
8
O
FF
OFF
O
N
3200
16
OFF
OFF
OFF
6400
32
2
)
Current setting
:
Dip switches
4
,
5
, and
6
correspond to S
4
, S
5
, and S
6
, respectively.
S
4
S
5
S
6
Cuurent(A)
ON
ON
ON
0.
5
ON
OFF
ON
1.0
ON
ON
OFF
1.5
ON
OFF
OFF
2.0
OFF
ON
ON
2.5
OFF
OFF
ON
2.8
OFF
ON
OFF
3.0
OFF
OFF
OFF
3.5
3
) Troubles
Alarm indicator
Reasons
Measures
LED off turn
Wrong connection for power
Check wiring of power
Low-voltages for power
Enlarge voltage of power
Motor doesn’t run, without holding torque
Wrong connection of stepper motor
Correct its wiring
RESET signal is effective when offline
Make RESET ineffective
Motor doesn’t run, butmaintains holding torque
Without input pulse signal
Adjust PMW & signal level
Motor runs wrong direction
Wrong wires’ connection
Change connection for any of 2 wires
Wrong input direction signal
Change direction setting
Motor’s holding torque is too small
Too small relative to current setting
Correct rated current setting
Acceleration is too fast
Reduce the acceleration
Motor stalls
Rule out mechanical failure
Driver does not match with the motor
Change a suitable driver
3. Power supply 200W-24V
4. breakout board
Built in DB25 male connector.
DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
DB25 Input Pin: P10,P11,P12,P13,P15.
DB25 GND Pin: P18-P25.
Power supply: +5V DC.
Built in C-class Optical-coupler.
General in the software
P2 P3 is set to X-axis for the X-axis pulse
P4 P5 is set to Y-axis, Y axis pulse
P6 P7 is set to Z-axis Z-axis pulse
The other can be set to A B C axis
A-axis pulse P8 P9 is set as the A axis
P14 is set to B-axis B-axis pulse P1
P16 P17 is set to C-axis, C axis pulse
Can also be set to the spindle control signal \ electrical permit
Input interface for the P10 P11 P12 P13 P15
Application:Our Stepper Motors are used on small to mid-sized CNC mills or milling machines, CNC lathes, Pick-n-place machines,Laser Engravers and Laser Cutters, Vinyl Sign Cutters, CNC Plasma Cutters, and CNC Foam Cutters. Carver machine ,Dispenser,Automazation,3D Printer,Stage lighting,instrument,laser equipment,scanner and so on.These motors have been used in precision telescope positioning systems and robots.
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
We accept ebay payment 。
Fees such as import duties, taxes are not included in the item price or shipping costs. These charges are the buyer's responsibility.
Delivery details
Shipping:
The item will be shipped from our US warehouse to United States, which is more faster than from aboard.
2-9 working days to: USA
Terms of sales
We maintain high standards of excellence and strive for hundred percent customer satisfaction. Feedback is very important to us. We hope that you contact us immediately before you give neutral or negative feedback, so that we can address your concerns. It is impossible to address issues if we do not know about them!
About us
Your satis
faction is our ultimate goal. We work hard to earn your trust and future business. Our certified technicians have tested each item before shipping. The unit comes with 1 year limited warranty on all manufacturing defects.
a) If you receive a defective item, you may return it or ask for a discount. Please contact us within 14 days after you receive the package.
b) What you returned must be intact and in its original packaging as re? u. Customer is responsible for shipping costs of the returned item.
c) We will cover the cost of shipping back t with the shipping rate indicated in the registration page. We will send you a new unit or refund the full payment you paid.
Thank you.
Contact us
Business Hour
Business Hour: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
: Monday To Friday: 8:30 AM to 5:00 PM (Beijing China time)
Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply your email within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday.
Please contact us with ebay message.
Please feel free to contact us if you have any questions.
Feedback
On Jun-22-21 at 18:35:14 PDT, seller added the following information: